Button Badge Rings – Die Height Washer Spacer | 58mm & 44mm
Button Badge Rings – Die Height Washer Spacer | 58mm & 44mm - 58mm + 44mm Set इसका बैकऑर्डर दिया गया है और जैसे ही यह स्टॉक में वापस आएगा, इसे भेज दिया जाएगा।
पिकअप उपलब्धता लोड नहीं की जा सकी
Button badge rings are black die height washers for 58 mm and 44 mm round badge presses. Place in the die recess to raise pressing height when shells, mylar, and backs do not match your machine — improves compatibility but is not guaranteed on every model. Combo set saves vs buying both sizes separately.
चेकआउट के दौरान क्रेडिट कार्ड के लिए ईएमआई विकल्प खोजें!
Button Badge Rings – Die Height Washer Spacer | 58mm & 44mm
Button Badge Rings — Height Washer for Badge Dies
Use these button badge rings as a die height washer when your badge press, mould, and raw material stack do not line up perfectly. The black spacer ring sits in the outer recess of the die to raise the pressing height so shells, mylar, and paper can crimp more reliably across different machine and material combinations.
Important: This is a compatibility aid, not a universal fix. Results vary by press model, mould depth, and consumable thickness. Many shops see fewer half-presses and mis-crimps; some machine and material pairs still will not work — test on your setup before bulk production.
Key Features
- Die Height Spacer: Washer-style ring increases effective die depth for thicker or mismatched badge stacks.
- 58 mm & 44 mm Sizes: Match the two most common round button badge diameters used in Indian print shops.
- Value Combo Set: Order the 58 mm + 44 mm pair together when you run both sizes on one bench.
- Rigid Black Finish: Flat profile with clean edges for repeatable placement in the die groove.
- Raw Material Friendly: Helps when switching between pin-back, magnet, or slightly different shell gauges on the same press.
- Made for Badge Makers: Ideal add-on for button badge machine owners, sublimation badge units, and ID print studios.
How to Use
- Press a test badge without the ring and note if the curl is shallow, paper tears, or the back does not lock.
- Place the correct size ring in the outer die recess (see comparison photo in gallery).
- Load shell, artwork, mylar, and back as usual; press again and inspect the curl and back lock.
- Keep the ring installed only when it improves your stack — remove it if the press becomes too tight.
Best For
- Shops mixing 58 mm and 44 mm badge lines on shared equipment
- Operators troubleshooting height mismatch between dies and consumables
- Spare-part stock for field service and training demos
Pair with 58 mm and 44 mm button badge raw material, machines, and cutters from AbhishekID for a complete badge workflow.
Technical Details — Button Badge Rings
| Feature | Description |
| Product Type | Button badge die height washer / spacer ring (accessory) |
| Function | Increases effective die height for badge pressing when material stack depth varies |
| Available Sizes | 58 mm (round badge class) · 44 mm (round badge class) · Combo: 58 mm + 44 mm set |
| Colour | Black |
| Profile | Flat annular washer; sits in outer die recess |
| Compatibility Note | Helps many machine + raw material combinations; not 100% effective on all presses or moulds — test before production runs |
| Typical Use | Pin-back, magnet, and standard shell stacks where curl or back lock is shallow |
| Industry Reference | Round badge diameters align with common 58 mm and 44 mm button badge consumables sold in India |
| Unit Pricing | 58 mm or 44 mm single ring — MRP ₹300, sell ₹200 each; Combo set — ₹300 (save vs two singles) |
| Brand | AbhishekID |
FAQs — Button Badge Rings
| Question | Answer |
| What is a button badge ring used for? | It is a washer-style spacer that fits in the badge die to increase pressing height so shells, print, mylar, and backs crimp correctly when your stack is slightly too thin or your die depth does not match the consumables. |
| Which size ring do I need — 58 mm or 44 mm? | Choose the ring that matches your round badge size class: 58 mm for standard 58 mm button badges, 44 mm for 44 mm badges. The ring outer diameter matches the die size you are running. |
| Will this fix every badge machine? | No. It improves compatibility for many presses and material mixes, but it is not guaranteed on all models or moulds. Always run test presses before bulk orders. |
| How do I install the ring? | Place the ring in the outer recessed groove of the die (see gallery comparison). Load components normally and press. Remove the ring if the press feels over-tight or components buckle. |
| Can I use one ring for magnet and pin-back badges? | Often yes, when the only issue is stack height. Magnet and pin-back parts have different thicknesses — the ring helps bridge that gap, but results still depend on your specific mould and shells. |
| What is included in the 58 mm + 44 mm set? | One 58 mm ring and one 44 mm ring — priced at ₹300 so shops running both sizes save versus buying two singles at ₹200 each. |
| Is this a consumable or a machine part? | It is a reusable accessory. Keep rings clean and replace only if cracked or warped from heat or impact. |
| Does AbhishekID sell matching raw material and machines? | Yes — browse 58 mm and 44 mm button badge blanks, machines, and cutters on AbhishekID to build a full badge production line. |
